Selectively routing Plex through your VPN

Stay Updated

How To Set Up Plex Media Server Port Forwarding Avoid Buffering
Sharing Plex without port forwarding Plex, by default, will set up the port as and will require it to be forwarded through your router to the destination in this case, your Plex server. Ubuntu you may have to use another command depending on your distro. It says I do not have permission to add this to the file? This process is going to vary depending on your router manufacturer. Once you do this make sure you port forward as well and I would recommend reserving your address on your router for the PC running the plex server. Post Your Answer Discard By clicking "Post Your Answer", you acknowledge that you have read our updated terms of service , privacy policy and cookie policy , and that your continued use of the website is subject to these policies. Protocol dictates what kind of traffic is allowed to be forwarded.

How to Enable Remote Access

local plex media server ip address

But for that experience to work, your computer needs to phone home to Plex and authenticate. Thankfully, there are two easy ways around the problem: Before we proceed, there are two very important caveats.

First and foremost, you must make these changes in advance. You have to be online and logged into your Plex account to make changes to your local Plex Media Server. There is no way around this. The first order of business is to hop into your Plex Media Server via the web-based control panel, located, by default, at https: This tells me that my Plex server has an IP address of The Plex default port is always in fact, so while your IP will vary, the port should also say Then, you need to log in to your router admin page again, and find the section on port forwarding instructions for Linksys and Netgear.

Finally, restart your router, head back to your Plex server settings, and attempt to enable remote access again. However, your devices are probably set up to get an IP automatically via DHCP, which means they could change when you restart your router.

A static IP address doesn't change. What are the advantages to this, and why would you want one? Read More , but the results are similar. On a Unifi system, you can click on the device from the Client list, then on the Configuration tab, and expand the Network dropdown.

Tick the box to Use fixed IP address , and save—it should default to whatever IP it has now, but feel free to change it to something more memorable, then reconnect the device to get the new IP. Nearly everyone has experienced limited Wi-Fi functionality and poor coverage, especially in crowded areas. An Ubiquiti UniFi network could be the solution. Here's what you need to know. Your email address will not be published. Hi Martyn, thanks for commenting.

I will need to update the article. For now, after you connect to IPVanish, please open a command prompt and type: That will add the necessary static route, but is a temporary fix. Thanks again for your help.

I tried your suggestions but could not ge the route command to work with a symbolic ip address. I have managed to get things working to an extent by looking at my outgoing connetions when I enable the plex server and route these specifics direct to my router rather than the IPVanish. This needs reset each connection which is a pain, do you have any other suggestions I could try?

The parameter is incorrect. I have double checked all my info and subnet mask and default gateway are definitely the above any idea or a permanent solution to this? Is it possible to route plex around NordVPN?

And how would I do that? I asked them and they told me that its not possible. But after reading this guide, im thinking there might be a way. Hi Jakob, thanks for reading! I have a workaround for you. There are two steps, and it will take about 10 minutes. In practice that means every time you go to plex. In order to force plex. Add this line to the end of your hosts file:. Save your changes and restart your computer to make sure the changes have taken effect.

Keep the command prompt open for the next step. In order to let plex. You can do that with this console command:. If you have problems, let me know. The only config file in there is openvpn. See the owner of the file or an administrator to obtain permission. Hi Nick, thanks for reading. My guess would be that your static IP address is being set incorrectly. In general, take a look at your network properties when your computer is connected and working. I know that could be a bit clearer.

Probably just have the wrong number typed in somewhere. The reason we add an exception to plex. That lets a Plex client, like your firestick, find your home Plex server.

A great article — Thanks. How would these instructions differ to get the VPN to accept the Plex settings? Hi Tim, thanks for reading. Thanks for your article, great stuff.

Just one simple question if I start using IPVanish with the workaround in the config file as described. Is traffic going to plex. Hi John, thanks for reading. The answer to your question is yes and no. The traffic to plex. The rule that is added to the config file tells IPVanish to allow your computer to connect directly to plex.

Requirements for Plex Remote Access

Leave a Reply

Mar 04,  · Check the IP Addresses of devices/computers directly connected to the Airport Extreme and compare with the IP Address of the MAC hosting the Plex Media Server. I believe on a Mac you can find out the IP Address . May 05,  · Upload the Plex Media mackledaddy.tk using 'More Reply Options' and give the local IP Address and time the test was carried out The step about restarting Plex Media Server (in reporting issues topic) is actually important for this problem as there has been a report that LG Smartshare does not work after computer wakes from sleep. Change the password on your Plex account. plexwatch or Plex Notify or some other such program may tell you the IP address but I have found it not to work % of the time. permalink embed.